Accuracy
The table below shows the accuracy of TZ specifications.
Accuracy
unit: mm
| Model and size | Wedge reduction ratio |
Positioning repeatability |
Positioning accuracy |
Lost motion | Parallelism in table elevating |
Squareness in table elevating |
|---|---|---|---|---|---|---|
| TZ120X -2 | 1:2 | ±0.001 | － (0.005) |
0.001 | 0.010 | 0.010 |
| TZ120X -4 | 1:4 | |||||
| TZ200H -2 | 1:2 | ±0.001 | － (0.005) |
－ | － | － |
| TZ200H -4 | 1:4 | |||||
| TZ200X -2 | 1:2 | ±0.001 | － (0.005) |
0.001 | 0.010 | 0.010 |
| TZ200 -4 | 1:4 |
| Remark: | The values in （ ） indicate values with a linear encoder. |
Maximum speed
The table below shows the maximum speeds for various TZ specs.Consult IKO when considering using at speeds exceeding the maximum speed.
Maximum speed
| Model and size | Wedge reduction ratio |
Ball screw lead mm |
Maximum speed mm/s |
|
|---|---|---|---|---|
| AC servomotor | Stepper motor | |||
| TZ120X -2 | 1:2 | 4 | 100 | 60 |
| TZ120X -4 | 1:4 | 50 | 30 | |
| TZ200H-2 | 1:2 | 5 | 125 | 75 |
| TZ200H-4 | 1:4 | 62.5 | 37.5 | |
| TZ200X-4 | 1:2 | 125 | 75 | |
| TZ200X-4 | 1:4 | 62.5 | 37.5 | |
| Remark: | To measure the practical maximum speed, it is required to consider operation patterns based on the motor to be used and load conditions. |
Maximum carrying mass
The table below shows the Maximum carrying mass.Consult IKO when considering using the product under loads exceeding Maximum carrying mass.
Maximum carrying mass
| Model and size | Wedge reduction ratio |
Carrying mass position mm |
Maximum carrying mass Kg |
|||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Length L Horizontal direction |
Length L Vertical direction |
|||||||||
| Height H | 0 | 100 | 200 | 300 | 0 | 100 | 200 | 300 | ||
| TZ120X | 1:2 | 0 | 146 | 45 | 25 | 18 | 10 | 10 | 6 | 4.5 |
| 100 | 95 | 37 | 23 | 16 | 10 | 7 | 5 | 3.8 | ||
| 200 | 61 | 31 | 20 | 15 | 6 | 5 | 4.1 | 3.3 | ||
| 300 | 45 | 26 | 18 | 14 | 4.4 | 3.7 | 3.2 | 2.8 | ||
| 1:4 | 0 | 146 | 46 | 26 | 18 | 10 | 10 | 6 | 4.6 | |
| 100 | 98 | 37 | 23 | 16 | 10 | 8 | 5 | 3.8 | ||
| 200 | 63 | 31 | 20 | 15 | 6 | 5 | 4.2 | 3.3 | ||
| 300 | 46 | 26 | 18 | 14 | 4.5 | 3.8 | 3.2 | 2.8 | ||
| TZ200H | 1:2 | 0 | 109 | 59 | 35 | 25 | 9 | 9 | 7 | 5 |
| 100 | 88 | 45 | 30 | 22 | 9 | 7 | 5 | 4.3 | ||
| 200 | 59 | 36 | 26 | 20 | 6 | 5 | 4.2 | 3.6 | ||
| 300 | 44 | 30 | 23 | 18 | 4.5 | 3.8 | 3.3 | 2.9 | ||
| 1:4 | 0 | 109 | 62 | 37 | 26 | 10 | 10 | 8 | 5 | |
| 100 | 95 | 47 | 31 | 23 | 10 | 8 | 6 | 4.6 | ||
| 200 | 62 | 38 | 27 | 20 | 7 | 5 | 4.7 | 3.9 | ||
| 300 | 46 | 31 | 23 | 18 | 5 | 4.3 | 3.7 | 3.2 | ||
| TZ200X | 1:2 | 0 | 159 | 123 | 72 | 51 | 9 | 9 | 9 | 9 |
| 100 | 159 | 119 | 71 | 51 | 9 | 9 | 9 | 9 | ||
| 200 | 159 | 112 | 70 | 50 | 9 | 9 | 9 | 9 | ||
| 300 | 159 | 103 | 67 | 49 | 9 | 9 | 9 | 9 | ||
| 1:4 | 0 | 160 | 124 | 73 | 51 | 10 | 10 | 10 | 10 | |
| 100 | 160 | 120 | 72 | 51 | 10 | 10 | 10 | 10 | ||
| 200 | 160 | 113 | 70 | 50 | 10 | 10 | 10 | 10 | ||
| 300 | 160 | 105 | 68 | 49 | 10 | 10 | 10 | 10 | ||
| Remark: | The maximum carrying mass is adjusted by the mass when the rating life of the linear motion rolling guide, ball screws, or bearings is 18,000 hours during continuous operation at a number of revolutions of the motor of 3000min-1 and an acceleration/deceleration time of 0.2s. The mass calculated is based upon the basic static load rating of the linear motion rolling guide. |
Some products are not shown in the catalogue. Also, modifications can be made to meet your requirements. Please do not hesitate to make inquiries.
